Hello everyone, today I will answer some questions about the installation of the washbasin, including how to install the washbasin. Many people still don’t know, so, today I will answer some questions about the installation of the washbasin. Let’s analyze it for everyone, now let’s take a look! If your problem is solved, I hope you will pay attention to this site, thank you~
Table of contents of this article
- How to install the overflow hole of the wash basin correctly
- How to install the square wash basin
- How to install the bath basin
- How to install the top and bottom of the bathroom washbasin washing machine
- How to install a washbasin
- How to install a slate washbasin
1. Correct installation method of wash basin overflow hole
Now drain hole Put a circle of glass glue around it. It must be a full circle to ensure that there will be no leakage.
Put the stainless steel drain device into the drain hole and press it tightly to allow the glass glue to fully adhere.
Screw the round plastic ring into the stainless steel cage of the drain, remember to lock it, and then install the drain of the overflow part and insert the rubber pad In the groove, pay attention to the tightness, place the overflow drain device in place, and lock the screws on the front.
The next step is the drain. First install the anti-odor floor drain: Generally, the floor drain and the sewer pipe will not be completely sealed, so you can use raw tape and wrap it around the floor drain a few times. On the other hand, stuff the drain pipe into the drain pipe so that the two are tightly sealed.
2. How to install a square wash basin
You have to read it first Is your wash basin a countertop basin or a pedestal basin? 1. For countertop basins, first install the hot and cold water inlet pipes and drain pipes on the basin, place them directly on the countertop, and then connect the water inlet pipes to the triangular valve on the wall to drain the water. Connect the pipe to the sewer pipe, open the valve and let out water to see if there is any leakage. If there is any leakage, tighten it. If there is no leakage, apply glass glue on the countertop and let it dry.
2. For the pedestal basin, you must first place the matching pillars in the reserved sewer pipe position. The sewer pipe is in the center of the pillar. Place the basin on the pillar, close to the wall, and place it horizontally. Some use The bracket is used to fix the basin. Some have screw holes under the basin and are directly fixed on the wall.
Mark the position of the screw holes on the wall. , remove the basin and column, drill holes in the wall, and after installing the steel expansion, move the column back to the designated position and install the water inlet pipe of the basin.
After the drainage pipe is installed, it can be installed. If you use expansion to fix the basin directly, just tighten the screws. Don\’t use too much force, otherwise you will break the basin.
After testing that there is no leakage, apply glass glue around the area where the pillar contacts the ground and where the basin contacts the pillar. Note that it is best to bend the drain pipe into a U-shape or S-shape to avoid odor
3. How to install the bathtub
1. First, we need to measure the installation size
2. After determining the position, you can use a level ruler to confirm it again and mark it on the wall with a pen.
3. Then use fixed metal parts, install the wash basin, and mark the holes for installing the fasteners.
4. Next, you need to use impact Drill holes at the mark and install the expansion tube
5. When you need to install the hook, be careful not to tighten the screw too much. You can try it first. Hang it. Then insert the metal piece to adjust according to the verticality of the wash basin and the wall.
5. Finally, we will install the other parts of the faucet. The metal parts are fixed. Then install the screws into the fixing bolts and tighten the bolts. At the same time, apply silicone on the ground to seal it to avoid water leakage in the future.
4. How to install the top and bottom of the bathroom washbasin and washing machine
When installing the bathroom washbasin and washing machine, you need to pay attention to the following points. First of all , Make sure the washbasin and washing machine are reasonably positioned for easy use and operation. Secondly, when installing the washbasin, you need to connect the faucet and sewer pipe and ensure that they are properly connected.The faucet is firmly fixed. When installing the washing machine, you need to connect the water inlet pipe and the drain pipe, and make sure the drain pipe is unobstructed. In addition, pay attention to the stability of the washbasin and washing machine. They can be fixed on the wall or the floor with screws to prevent shaking and tilting. Finally, after the installation is completed, check the faucets, sewer pipes and water inlet pipes for leaks to ensure safety and reliability.
5. How to install the washbasin
. Before installation, you need to Measure the size of the basin, take out the drawing and trace it over the wash basin, place it on the countertop and draw the opening line along the edge. After drawing the opening diagram, recheck it to see if there are any errors.
2. After determining the opening position, start cutting the table. Use a cutting machine to cut a large opening on the table along the opening line, and smooth the edges. , until no unevenness appears.
3. Install the marble countertop at the corner. Pay attention to ensuring that the space below can install drainage fittings, water supply pipes, inlet and outlet valve switches, etc.
4. Align the wash basin with the large cutting opening and gently place it into the marble countertop. Adjust the position and draw it along the edge of the wash basin with a pencil. Mark the contour lines to avoid installation errors.
5. Take out the wash basin, apply a circle of glass glue around the cutting edge line of the countertop, and then put the wash basin back in according to the outline just drawn. Go to the cutting opening, check whether the position is accurate and neat, then slowly flatten it and compact it, and wipe away the excess glass glue.
6. After the glass glue is dry, start installing the water inlet and drainage pipe fittings. Before installation, open the water valve to drain the water in the pipe 3- In 5 minutes, clean the pipes to prevent debris from blocking the water and drainage, and then assemble them one by one.
7. After the installation is completed, the acceptance work must not be missed. Carefully check whether the wash basin is installed securely and whether there are any leaks in the faucet connections.
6. How to install a slate washbasin
1. Preparation Work: Make sure the washbasin and installation location are clean and flat, and reserve the locations for water pipes and sewer pipes.
2.Place the slate washbasin in the installation position, confirm whether the position is appropriate, and ensure that the gap between it and the wall and floor is even.
3. Use a level to check whether the washbasin is level. If adjustments are needed, put wooden blocks or shims on the bottom of the washbasin for balance.
4. If there is no drainage hole reserved at the bottom of the washbasin, you need to use an electric drill and a suitable drill bit to drill a drainage hole to ensure that the size of the hole is suitable for the sewer pipe. connect.
5. Fix the washbasin to the wall and floor. Expansion bolts, angle irons or other suitable fixing materials can be used for fixing.
6. Connect the water pipe and sewer pipe. Use suitable plumbing connections to connect water pipes and drain pipes to the basin. Make sure the connection is tight and watertight.
7. Check whether the installation is complete. Check whether the water pipes and sewer pipes are normal, open the faucets and drains, and check whether there is water flowing out and drainage is smooth.
Please note that the above steps are only general installation guidelines. The specific installation steps may vary depending on the washbasin model, material and installation environment. . If you are not sure how to install it, it is recommended to ask a professional to install it or consult the relevant installation guide.
This ends the content about the installation of the washbasin. I hope it will be helpful to everyone.
