Hello fellow veterans, today I will share with you knowledge about hand-woven tapestries and tapestry weaving tutorials. I hope it will be helpful to you. If it can help you, please pay attention to this site and bookmark it. Your support is our biggest motivation. Thank you everyone. Let’s get started!
Contents of this article
- How to change threads in tapestry weaving
- Tapestry weaving tutorial
- Bohemian tapestry weaving tutorial
- Feather tapestry weaving tutorial
1. Tapestry How to change threads during weaving
1. First, confirm the location where threads need to be changed during tapestry weaving. If only a specific area of the thread is damaged or needs to be replaced, you can untie the thread in that area first.
2. Find the starting position where the thread needs to be replaced, and use scissors or a seam removal needle to remove the thread at that position.
3. Take out the new thread and select the appropriate thread according to the weaving style and color of the tapestry.
4. Pass the thread end of the new thread through the starting position of the thread to be replaced, and pull out the thread end to a sufficient length.
5. Using the knitting tools used for tapestry weaving (such as knitting needles or crochet hooks), thread the new thread through the original knitting structure.
6. During the replacement process, pay attention to maintaining the tightness of the weave to ensure a seamless connection between the old and new lines.
7. Continue to weave according to the original weaving method, completely alternating the new thread with the old thread.
8. When the new thread is braided to the end position where the thread needs to be replaced, firmly combine the thread ends of the new thread with the thread ends of the old thread to ensure the quality of the braiding.
9.Finally, trim and tidy up the threads in the woven area to match the look of the entire tapestry.
It should be noted that you should be careful when replacing threads to avoid damaging the appearance or structure of the tapestry. If you are not familiar with tapestry weaving and thread replacement, it is recommended to seek help from professionals or tapestry makers.
2. Tapestry weaving tutorial
1. First, you must have a loom or Use wooden sticks instead, but you need to carve lines on the upper and lower wooden sticks
3. Hand-drawn sketches can see the final effect and know the approximate proportions. .
4. All weaving is the same, you must wind the warp on the loom, and then start weaving the weft.
5. Weaving is very simple. The only thing to note is that two weft threads are used as a group, and the upper and lower rows must be staggered.
6. After weaving for a period of time, it must be tamped so that it will be tight and dense.
7. Use three strands of wool to make tassels.
8. Then start knitting threads of other colors, using the same method
9. The basic weaving is done here. Already completed.
10. Remove the threads from the loom and tie them into two knots.
11. Finally trim the tassels and you\’re done
3. Bohemian tapestry weaving tutorial
1. First, you need a wooden stick of about 50cm, which can also be replaced by dry branches.
2. Step 2: Start adding threads. Use lark knots to weave 20 threads onto the wooden sticks.
3. Step 3: Make seven flat knots. Knot, two rows.
4. Step 4: Cross the flat knot and combine the pattern. Fix the lower end with a flat knot and adjust it after completion. Spacing.
5. Step five, tie another row of flat knots. At present, each fork still exists independently.
6. Sixth Step 1, exchange the axes, and tie a flat knot again, this time the five crosses are connected into one piece!
7. Step 7, repeat the pattern with three crosses! Center.
8. Repeat the cross and center the pattern.
9. , the ninth step, add thread. Take four threads, reserve 90cm for the axis, and twist the threads.
What I did here is double thread. There is a thickness, and the length of the twist knot can be determined by yourself, just pull it until it has a curvature in the middle!
Just make it like this. If it is not long enough, you can add more threads. Don’t cut it off early.
10. Step 10: As a decoration, add a thin left and right knot on both sides, depending on the size. The layering is highlighted.
11. The eleventh step is to make the decorative patterns on both sides. They hook up together~
Recycle it again, and a diamond-shaped fishing net comes out
Obliquely! I won’t introduce too much about the combination of curly knots and flat knots~
12. Step 12, cut the tassels according to your needs and personal preferences, but Not too short.
13. Step 13, simply tie the rope with a left and right knot.
4. Feather tapestry weaving tutorial
Hello, the following is a feather tapestry weaving tutorial:
1. Sort the feathers and arrange them by color and size.
2. Place the wooden stick or copper pipe on the table and use Tie it in the center with thread
3. Tie the first feather to the stick with thread, making sure the bottom of the feather is in line with the stick.The sticks are flush.
4. Tie the second feather next to the first feather with a thread. Keep adding feathers until you are satisfied.
5. If you want to add lace or other decorations to the tapestry, you can use threads of different colors or add small beads and other decorations.
6. When you have finished the tapestry, tie the thread to the other end of the stick and tie rope or hooks to both ends of the stick for hanging. on the wall.
-Feathers can be real feathers or artificial feathers.
-If you want the tapestry to be fuller, tie some string or stuffing like wool under the feathers.
-If you want the tapestry to be more even, start by dividing equidistant areas on the sticks with line segments and then add feathers to each area.
This ends the content about hand-woven tapestries. I hope it will be helpful to everyone.
